Admin Table of Contents
What is the standard bore of a 454?
4.250-inch
The standard rod length on a 454 is 6.135-inch, and its bore size is 4.250-inch.
What is a 454 bored over?
According to Wikipedia the 454 has 454.2 CID via a 4.251 inch bore and a 4 inch stroke. ((4.251 / 2)^ 2) * pi = ~14.19 square inches. Multiply that by the 4 inch stroke and you have ~56.77 cubic inches, multiply that by 8 cylinders and you have ~454.17. So far so good, now, you bored it .
How much can a 454 block be bored?
They can safely be bored to 4.500 inches, which, even with the stock 454/502’s 4-inch-stroke crank, yields a displacement of 509 ci.
What cubic inch is a 454 bored 100 over?
On a 454ci engine with a stock, 4.00-inch stroke, a 0.100-inch overbore delivers a 476-inch displacement, while a 0.125-inch overbore will give you a 481-inch Rat. A popular combination is the safer 0.060-inch overbore with a longer, 4.250-inch stroke to make a 496-inch combination.
How big can you bore and stroke a 454?
Cubic Inch to Bore/Stroke Chart
| Mfgr | CID | Stroke |
|---|---|---|
| Chev | 434 | 4.125 |
| Chev | 454 | 3.781 |
| Chev | 461 | 3.98 |
| Chev | 502 | 3.59 |
What can a 454 be stroked to?
Best of all, they’re ripe for the stroker treatment. Take a 454, add a 4.250-inch stroke crank along with some 6.385-inch rods and your displacement shoots up to 489 cubes. Now bore those cylinders out a touch, to say . 060-inch over and you end up with the venerable 496.
Which Chevy big-block is the best?
Our Top 5 Big Block Chevys of All Time
- 396 L78. This is the original factory big block Mark IV engine from Chevrolet.
- 427 Tri-Power. The 427 big block was introduced as a production engine in 1966 for full-sized Chevrolets and Corvettes.
- 454 LS6.
How much HP can you get out of a 454?
Surprisingly, the 454 laid down an impressive 330 horsepower and 475 pound-feet of torque. Naturally, the truck-based 454s were tuned for torque, so having nearly 500 pound-feet wasn’t a big surprise. But like any stock engine, there was tons of power left to be squeezed out.
What is the difference between a 454 block and a 427 block?
BTW, 427, 454 blocks are identical, only difference is the stroke, and the 454 blocks are notched to accept the longer stroke. Rod lengthe between both are identical…they use the same rods. Power window circuit breaker question. Quick Reply: What cubic inch is a 454 bored .030 .040 and .060?
What’s a good rpm for a 454 block?
If you just have a .060 over 454 block you might as well go 496. More cubes are a good thing. 1966 Chevelle Malibu 489, 870 Holley, Edelbrock RPM Air Gap, aluminum heads Patriot 315, TH 400 Gearvendors OD/UD, 12″ disks up front and 9 inch with 3.50s.
What is the standard bore size for a 454?
Standard bore size for a 454 is 4.250″. 7 71nomad
Can you stroke a 454 to over 500cc?
.060 over = 467. Yes you can stroke a 454 to over 500ci. If you want a big bore, long stroke combo you would be better off with an aftermarket block. With aftermarket blocks you can get over 700ci.