Admin Table of Contents
What is the ratio of IPS flooring?
It is generally used for all types of floors and mix of concrete used for IPS flooring specification is 1:1.5:3 (cement, sand and stone aggregates). As per the nature of use the flooring thickness of concrete is decided from 25 mm to 50 mm.
What is difference between PCC and IPS flooring?
It is laid over the concrete base (1:4:8), which is almost 3 to 4 inches thick plain cement concrete (PCC) base. You can decide the thickness of the IPS flooring as per the requirement of work; in residential floor 75 mm floor thickness is sufficient whereas industrial floor thickness should be kept 150 mm.
What is the difference between VDF and IPS flooring?
Unlike IPS, a VDF floor calls for a more skilled labour with almost twice as many man hours over the same stretch….. This system raises the cost as there is machinery required, but appearance wise and strength wise the VDF (Vacuum Dewatered Floor) floor stands out……
Is code for concrete flooring?
IS 2571 : 1970
Basic Details
| IS Number : | IS 2571 : 1970 |
|---|---|
| Document Title [Eng-Hn] : | Code of practice for laying in – Situ cement concrete flooring (First Revision) |
| No of Revision : | 1 |
| No of Amendments : | 0 |
| Technical Department : | Civil Engineering Department |
What is the thickness of PCC in foundation?
The Thickness of PCC: The thickness of PCC is normally 50mm over Brick Flat Soling (BFS). If you don’t use BFS below PCC then the thickness should be 75¬mm.
What is Trimix road?
Tremix System also known as Dewatering System is used in making Industrial Floors, Concrete Roads, Runways, Railways Platforms, Warehouse container Yards, Canal Lining, Pathways, Bridges, RCC Roads, etc. The Tremix process gives the below properties to concrete: » Higher Compressive Strengths. » Faster Initial Strength.
What is M40 concrete?
M40 grade stands for it’s a mix of concrete with a characteristic compressive strength of 40 N/mm2. The mix design procedure for M40 grade concrete as per ACI Method is discussed.
Which mix is a M20 concrete mix?
Different grades of concrete :
| Type of Concrete | Concrete Grade | Mix Ratio |
|---|---|---|
| Ordinary concrete | M7.5 | 1:4:8 |
| M10 | 1:3:6 | |
| M15 | 1:2:4 | |
| M20 | 1:1.5:3 |
How thick should floors be?
In a typical home, the entire structure between levels can be about 12 to 14 inches thick, depending on the type of joists used and the finish materials for the floor and ceiling.
What is IPS flooring?
IPS flooring stands for Indian patent stone flooring, it is a basic type of flooring which provides good wearing properties. It is generally used for all types of floors and mix of concrete used for IPS flooring specification is 1:1.5:3 (cement, sand and stone aggregates).
What is the best way to finish an IPS concrete floor?
If glossy or smooth IPS flooring surface required then neat cement punning, 2 to 3 mm thick is spread over the IPS concrete surface and allowed to soak into the concrete. The surface is finished with metal trowel 3 to 4 times to give surface a glossy look.
How to prepare concrete for installed paving work?
Chipping and clearing of mortar dropping. Do prepare the surface on the concrete floor by hacking at close intervals (50 to 70 mm center to center) with bush hammer or with a chisel and hammer and then wash it thoroughly with water. This will roughen up the concrete surfaces and ensure a good bond is provided for the IPS concrete.
How to prepare concrete floor before installing a concrete slab?
As per the requirement and the direction of Project Manager. Chipping and clearing of mortar dropping. Do prepare the surface on the concrete floor by hacking at close intervals (50 to 70 mm center to center) with bush hammer or with a chisel and hammer and then wash it thoroughly with water.