What is the minimum configuration for the interface of a router that participates in IPv6 routing?

What is the minimum configuration for the interface of a router that participates in IPv6 routing?

Explanation: With IPv6, a router interface typically has more than one IPv6 address. The router will at least have a link-local address that can be automatically generated, but the router commonly has an global unicast address also configured.

How does routing work with IPv6?

Routing in IPv6 is almost identical to IPv4 routing under CIDR. The only difference is the addresses are 128-bit IPv6 addresses instead of 32-bit IPv4 addresses. With very straightforward extensions, all of IPv4’s routing algorithms, such as OSPF, RIP, IDRP, IS-IS, can be used to route IPv6.

How do I enable IPv6 routing on Cisco router?

Enable IPv6 routing on a Cisco router using the ipv6 unicast-routing global configuration command. This command globally enables IPv6 and must be the first command executed on the router. Configure the IPv6 global unicast address on an interface using the ipv6 address address/prefix-length [eui-64] command.

Does IPv6 need routing?

Routing in IPv6 is performed in the same way as IPv4 but it requires two distinct routing tables, one for IPv4 routes and another for IPv6 routes.

What is missing from the stateful DHCPv6 configuration on router R1?

What is missing from the stateful DHCPv6 configuration on router R1? The FA0/0 interface is missing the command that informs the clients to use stateful DHCPv6. The DHCPv6 pool has not been bound to the LAN interface.

How do I assign an IPv6 address to an interface?

Configuring IPv6 Addresses

1. In the Managed Network node hierarchy, navigate to the Configuration > Interfaces > VLANs tab.
2. Select a Vlan.
3. Select the corresponding Vlan.
4. Select the IPv6 tab and expand the IP Address Assignment accordion.
5. Enable Use Static addresses.
6. Click + in IPV6 addresses.

How do I use IPv6 instead of IPv4?

To enable IPv6, the switch icon in the upper right corner needs to be set to ON and the Addresses pop-up underneath set to Automatic. To disable IPv6, slide the IPv6 setting to OFF. Click Apply.

How do I verify IPv6 configuration?

Via the AmpliFi app

1. Open your AmpliFi smartphone app.
2. Tap the image of the router to open the router’s settings.
3. Select the “Internet”.
4. Scroll down to “IPv6” and toggle this On.
5. Verify corresponding Network Type.
6. Tap the check mark on the top right corner to save your settings.

How do I configure IPv6 addressing?

In Settings go to Network & Internet and click the Properties button for the interface you wish to configure. Click the Edit button under IP settings, change the configuration type to Manual, enable IPv6, and populate your settings.

How do I configure IPv6 routing?

Configuring an IPv6 Router

1. Ensure that you have completed the required prerequisites before you begin IPv6 configuration.
2. Configure a router.
3. Configure tunnel interfaces on the router.
4. Configure the switches on the network.
5. Configure any hubs on your network.
6. Configure the network name service for IPv6.

What’s the minimum number of network ports needed on a router to be functional?

three ports
Routers have multiple port connections for connecting to the LANs, and by definition a router must have a minimum of three ports. The common symbol used to represent a router in a networking drawing is provided in Figure 5-14.

What is the minimum configuration for a router interface participating in IPv6?

4. What is the minimum configuration for a router interface that is participating in IPv6 routing? Explanation: With IPv6, a router interface typically has more than one IPv6 address. The router will at least have a link-local address that can be automatically generated, but the router commonly has an global unicast address also configured.

Do all IPv6 enabled interfaces need to have a link-local address?

Explanation: All IPv6 enabled interfaces must at minimum have a link-local address. Other IPv6 addresses can be assigned to the interface as required.

What command will enable a router to configure a link-local address?

What command will enable a router to begin sending messages that allow it to configure a link-local address without using an IPv6 DHCP server? To enable IPv6 on a router you must use the ipv6 unicast-routing global configuration command or use the ipv6 enable interface configuration command.

What does a successful Ping to the IPv6 address mean?

IP is properly installed on the host. Explanation: The IPv6 address ::1 is the loopback address. A successful ping to this address means that the TCP/IP stack is correctly installed. It does not mean that any addresses are correctly configured.