How do I assign a VLAN across two switches?

How do I assign a VLAN across two switches?

Create the VLANs:

1. Open a web browser.
2. In the address bar of the web browser, type the IP address of the switch and press Enter.
3. Type the admin password of the switch and click Login.
4. Go to Switching – VLAN – Advanced – VLAN Configuration.
5. In the VLAN ID field, type the ID of the VLAN you wish to create and click Add.

How do I assign a trunk to a VLAN on a Cisco switch?

1. SUMMARY STEPS. enable. configure terminal.
2. interface interface-id. switchport mode trunk. switchport trunk allowed vlan {add | all | except | remove} vlan-list.
3. end. show interfaces interface-id switchport. copy running-config startup-config.

How do I assign a trunk port to a VLAN?

perform these steps:

1. To restrict the traffic that a trunk carries, issue the switchport trunk vlan-list interface configuration command.
2. To add a VLAN to the trunk, issue the switchport trunk allowed vlan add vlan-list command.
3. This example shows how to remove VLANs 5 through 10 and 12.

What is the purpose of a trunk between to switches?

The main purpose of trunking is to carry traffic between switches and maintain the VLAN information. Unlike an access link, the trunk link does not belong to a single VLAN but instead can carry traffic from several VLANs over a point-to-point link between two devices that understand the protocol.

What is difference between VLAN access and trunk mode?

The trunk port supports only the tagged frames, whereas the Access port sends and receives untagged frames. The trunk port allows us to switch multiple VLANs, but all frames are in the same VLAN in the Access port.

Which four steps are needed to configure a voice VLAN on a switch?

Which four steps are needed to configure a voice VLAN on a switch port? (Choose four). Add a voice VLAN. Assign a data VLAN to the switch port. Configure the interface as an IEEE 802.1Q trunk.

Can VLAN span multiple switches?

VLANs can span multiple switches, and you can have more than one VLAN on each switch.

What is the difference between access and trunk port?

What is the difference between an access port and a trunk port? An access port is a connection on a switch that transmits data to and from a specific VLAN. A trunk port allows you to send all those signals for each switch or router across a single trunk link.

What is trunk port in Cisco switches?

A trunk port is by default a member of all the VLANs that exist on the switch and carry traffic for all those VLANs between the switches. To distinguish between the traffic flows, a trunk port must mark the frames with special tags as they pass between the switches.

What are the steps to configure a VLAN on a switch?

To create VLAN interfaces:

1. Determine the IP addresses that you want to assign to the VLAN interfaces on the switch.
2. Open a web browser.
3. In the browser address field, type the IP address of the smart switch.
4. Type the password in the Password field.
5. Click the Login button.
6. Select Routing>IP>IP Configuration.

What is the difference between VLAN access and trunk mode?

An access port is a connection on a switch that transmits data to and from a specific VLAN. A trunk port allows you to send all those signals for each switch or router across a single trunk link. In contrast to an access port, a trunk port must use tagging in order to allow signals to get to the correct endpoint.

What two requirements must be met to configure VLAN Trunking Protocol?

To configure the VLAN trunking protocol to communicate VLAN information between two switches, what two requirements must be met? 1. Each end of the trunk link must be set to the IEEE 802.1e encapsulation. 2. The VTP management domain name of both switches must be set the same. 3. All ports on both the switches must be set as access ports. 4.

How many VLANs can be configured on a switch?

In this example, each switch is configured with 2 VLANs (10 and 20). There is a link between the switches over which traffic for both VLANs can pass. This is referred to as the VLAN Trunk Link. In this example, the VLAN port membership on each switch is the same.

How do I set up a VLAN trunk link?

Go to Switching – VLAN – Advanced – VLAN Membership. In the VLAN ID drop down menu, select VLAN 10. Mark ports 1, 2, 3, 4 & 5 with a U. This designates an untagged port and is used for ports which connect to client devices such as as PCs. Mark port 20 with a T. This designates a tagged port and is used for the VLAN trunk link. Click Apply.

How do I set up a VLAN for Port 20?

Mark port 20 with a T. This designates a tagged port and is used for the VLAN trunk link. Click Apply. In the VLAN ID drop down menu, select VLAN 20.