How much space do you need for a bathtub?

How much space do you need for a bathtub?

While there are no code requirements for tub size, minimum clear floor space alongside a bathtub should be at least 60 inches long (the length of a standard tub) and 30 inches wide. Always allow clear space for access to plumbing and/or whirlpool motors.

What is the rough opening size for a bathtub?

The standard rough-in dimension for a bathtub is 60-¼”. But if there’s a gap, you can attach furring strips to the stud wall. You can also apply some cement or plywood.

How do you measure for a new bathtub?

Using a power tape, measure the edge of the tub from one end to another for height and width. To measure the height of the bathtub, take measurement from the floor to the top. If you don’t get a round figure, take a number that is close to the standard size, that is listed below.

How much space do you need between freestanding tub and wall?

How far should the distance be between freestanding tub and wall? The distance between your tub and wall should be between 15-18 inches or at least 1 foot.

How do you measure a bathtub opening?

To measure your tub, Victoria Plum suggests starting with the length, which is found by beginning at the farthest edge of your tub and going to the other extremity. Make sure your measuring tape reaches the outer edges of your tub and not just the inner curve of the tub.

How far from the wall should a tub drain be?

You will need to cut a hole in the floor at the drain end of the tub to position the tub drain and install it. The hole should be at least 9 inches wide and 12 inches from the wall.

What is the difference between a soaking tub and a bathtub?

Deeper than the average bathtub, soaking tubs are designed to offer the ultimate in relaxation by allowing you to fully submerge. Some soakers can hold as many as 250 gallons of water, while the average bathtub holds between 25 and 45 gallons.

How is bathtub depth measured?

Standard tub depths allow for approximately 12” of water; soaking tubs should offer at least 14” or more so that the water covers the majority of the bather’s body. To determine water depth, measure the tub from the bottom (interior) to the overflow drain.

How close can a vanity be to a tub?

When deciding on placement, make sure there is at least 30 inches of floor space between the vanity and tub. The National Kitchen & Bath Association recommends a minimum of 30 inches of clear floor space alongside a tub. It also recommends a minimum of 30 inches by 48 inches of clear floor space in front of a sink.

What is a good size for a freestanding tub?

The Most Common Freestanding Tub Sizes While the most common freestanding tub models are usually 4.5 ft. to 6 ft. long, we think the 60” long freestanding tub size is the most universally appealing to American homeowners.

How big is a 2 person bathtub?

In terms of the dimensions of the perfect two-person bathtub, you’ll want to look for a unit measuring approximately 1500mm-1800mm x 700mm-800mm.

What height should a bath be set at?

The standard bath height is 510mm. Although heights may vary, it is important to remember that the higher the bath is, the harder it is to get in an out. That is particularly important to consider in family homes or homes for older people. Freestanding baths are a great choice if you have enough space to install one.

What are the standard dimensions of a bathtub?

Common or standard dimensions for a freestanding bathtub are: 60 inches long (5ft), 30 inches wide (2.5ft) with 19 inches of water depth (1.89ft). Small freestanding bathtubs can run 55 inches long(4.58ft), 27 inches wide (2.25ft) with a water depth of 15(1.25ft).

What is the size of a standard bathroom tub?

Standard Bathtubs. The two most common tub sizes are 60 inches long by 30 inches wide and 60 inches long by 32 inches wide. A standard rectangular-shaped tub, however, will have a smaller dimensioned bathing well, measuring 55 inches by 24 inches at the top and narrowing to 45 inches by 22 inches at the very bottom.

What are the dimensions of a typical toilet?

Typical toilet dimensions. Total height of one piece gravity toilet might vary from 21 to 30 3/4 inches (53 – 78 centimeters) with 14” – 16” (356 – 406 mm.) distance from the floor to bowl rim. Depth usually stays within 27” – 30” (686 – 762 mm) and width very rarely exceed 20 in (508 mm).

What is the standard size of a cast iron tub?

A standard rectangular-shaped tub, however, will have a smaller dimensioned bathing well, measuring 55 inches by 24 inches at the top and narrowing to 45 inches by 22 inches at the very bottom. These are general bathtub dimensions for both cast iron and fiberglass tubs.